|
|
Reversing motor starter, Size 1, Three phase full voltage, Solid-state overload relay, OLR amp range 0.25-1A, 110V 50Hz / 120V 60Hz coil, Non-combination type, Enclosure type 1, Indoor general purpose use, Standard width enclosure | |
| product brand name | Class 22 | |
| design of the product | Full-voltage reversing motor starter | |
| special product feature | ESP200 overload relay | |
| General technical data | ||
| weight [lb] | 23 lb | |
| Height x Width x Depth [in] | 20 × 12 × 8 in | |
| touch protection against electrical shock | NA for enclosed products | |
| installation altitude [ft] at height above sea level maximum | 6560 ft | |
| ambient temperature [°F] | ||
| ● during storage | -22 … +149 °F | |
| ● during operation | -4 … +104 °F | |
| ambient temperature | ||
| ● during storage | -30 … +65 °C | |
| ● during operation | -20 … +40 °C | |
| country of origin | USA | |
| Horsepower ratings | ||
| yielded mechanical performance [hp] for 3-phase AC motor | ||
| ● at 200/208 V rated value | 0.17 hp | |
| ● at 220/230 V rated value | 0.17 hp | |
| ● at 460/480 V rated value | 0.33 hp | |
| ● at 575/600 V rated value | 0.5 hp | |
| Contactor | ||
| size of contactor | NEMA controller size 1 | |
| number of NO contacts for main contacts | 3 | |
| operating voltage for main current circuit at AC at 60 Hz maximum | 600 V | |
| operational current at AC at 600 V rated value | 27 A | |
| mechanical service life (operating cycles) of the main contacts typical | 10000000 | |
| Auxiliary contact | ||
| number of NC contacts at contactor for auxiliary contacts | 0 | |
| number of NO contacts at contactor for auxiliary contacts | 1 | |
| number of total auxiliary contacts maximum | 8 | |
| contact rating of auxiliary contacts of contactor according to UL | 10A@600VAC (A600), 5A@600VDC (P600) | |
| Coil | ||
| type of voltage of the control supply voltage | AC | |
| control supply voltage | ||
| ● at AC at 50 Hz rated value | 110 V | |
| ● at AC at 60 Hz rated value | 120 V | |
| holding power at AC minimum | 8.6 W | |
| apparent pick-up power of magnet coil at AC | 218 VA | |
| apparent holding power of magnet coil at AC | 25 VA | |
| operating range factor control supply voltage rated value of magnet coil | 0.85 … 1.1 | |
| percental drop-out voltage of magnet coil related to the input voltage | 50 % | |
| ON-delay time | 19 … 29 ms | |
| OFF-delay time | 10 … 24 ms | |
| Overload relay | ||
| product function | ||
| ● overload protection | Yes | |
| ● phase failure detection | Yes | |
| ● asymmetry detection | Yes | |
| ● ground fault detection | Yes | |
| ● test function | Yes | |
| ● external reset | Yes | |
| reset function | Manual, automatic and remote | |
| trip class | CLASS 5 / 10 / 20 (factory set) / 30 | |
| adjustable current response value current of the current-dependent overload release | 0.25 … 1 A | |
| make time with automatic start after power failure maximum | 3 s | |
| relative repeat accuracy | 1 % | |
| product feature protective coating on printed-circuit board | Yes | |
| number of NC contacts of auxiliary contacts of overload relay | 1 | |
| number of NO contacts of auxiliary contacts of overload relay | 1 | |
| operational current of auxiliary contacts of overload relay | ||
| ● at AC at 600 V | 5 A | |
| ● at DC at 250 V | 1 A | |
| contact rating of auxiliary contacts of overload relay according to UL | 5A@600VAC (B600), 1A@250VDC (R300) | |
| insulation voltage (Ui) | ||
| ● with single-phase operation at AC rated value | 600 V | |
| ● with multi-phase operation at AC rated value | 300 V | |
| Enclosure | ||
| degree of protection NEMA rating | 1 | |
| design of the housing | indoors, usable on a general basis | |
| Mounting/wiring | ||
| mounting position | Vertical | |
| fastening method | Surface mounting and installation | |
| type of electrical connection for supply voltage line-side | Screw-type terminals | |
| tightening torque [lbf·in] for supply | 35 … 35 lbf·in | |
| type of connectable conductor cross-sections at line-side at AWG cables single or multi-stranded | 1x (14 … 2 AWG) | |
| temperature of the conductor for supply maximum permissible | 75 °C | |
| material of the conductor for supply | AL or CU | |
| type of electrical connection for load-side outgoing feeder | Screw-type terminals | |
| tightening torque [lbf·in] for load-side outgoing feeder | 20 … 24 lbf·in | |
| type of connectable conductor cross-sections at AWG cables for load-side outgoing feeder single or multi-stranded | 2x (14 … 10 AWG) | |
| temperature of the conductor for load-side outgoing feeder maximum permissible | 75 °C | |
| material of the conductor for load-side outgoing feeder | CU | |
| type of electrical connection of magnet coil | Screw-type terminals | |
| tightening torque [lbf·in] at magnet coil | 5 … 12 lbf·in | |
| type of connectable conductor cross-sections of magnet coil at AWG cables single or multi-stranded | 2x (16 … 12 AWG) | |
| temperature of the conductor at magnet coil maximum permissible | 75 °C | |
| material of the conductor at magnet coil | CU | |
| type of electrical connection for auxiliary contacts | Screw-type terminals | |
| tightening torque [lbf·in] at contactor for auxiliary contacts | 10 … 15 lbf·in | |
| type of connectable conductor cross-sections at contactor at AWG cables for auxiliary contacts single or multi-stranded | 1x (12 AWG), 2x (16 … 14 AWG), 2x (18 … 16 AWG) | |
| temperature of the conductor at contactor for auxiliary contacts maximum permissible | 75 °C | |
| material of the conductor at contactor for auxiliary contacts | CU | |
| type of electrical connection at overload relay for auxiliary contacts | Screw-type terminals | |
| tightening torque [lbf·in] at overload relay for auxiliary contacts | 7 … 10 lbf·in | |
| type of connectable conductor cross-sections at overload relay at AWG cables for auxiliary contacts single or multi-stranded | 2x (20 … 14 AWG) | |
| temperature of the conductor at overload relay for auxiliary contacts maximum permissible | 75 °C | |
| material of the conductor at overload relay for auxiliary contacts | CU | |
| Short-circuit current rating | ||
| design of the fuse link for short-circuit protection of the main circuit required | 10kA@600V (Class H or K); 100kA@600V (Class R or J) | |
| design of the short-circuit trip | Thermal magnetic circuit breaker | |
| maximum short-circuit current breaking capacity (Icu) | ||
| ● at 240 V | 14 kA | |
| ● at 480 V | 10 kA | |
| ● at 600 V | 10 kA | |
| certificate of suitability | NEMA ICS 2; UL 508; CSA 22.2, No.14 | |
| Further information | ||
|
Industrial Controls – Product Overview (Catalogs, Brochures,…)
www.usa.siemens.com/iccatalog
|
||
|
Industry Mall (Online ordering system)
https://mall.industry.siemens.com/mall/en/us/Catalog/product?mlfb=US2:22DUA32BF
|
||
|
Service&Support (Manuals, Certificates, Characteristics, FAQs,…)
https://support.industry.siemens.com/cs/US/en/ps/US2:22DUA32BF
|
||
|
Image database (product images, 2D dimension drawings, 3D models, device circuit diagrams, EPLAN macros, …)
http://www.automation.siemens.com/bilddb/cax_de.aspx?mlfb=US2:22DUA32BF&lang=en
|
||
|
Certificates/approvals
https://support.industry.siemens.com/cs/US/en/ps/US2:22DUA32BF/certificate
|
||
|
|
||
|
|
||
|
|
||
| last modified: | 1/25/2022 | |
| Date 5/20/2023 |
Subject to change without notice © Copyright Siemens 2023 |
|
原创文章，作者：[db:作者]，如若转载，请注明出处：https://www.zhaoplc.com/plc819270.html
微信扫一扫 
支付宝扫一扫